Downton downtown

By -

I had a little retail therapy the other weekend.

There was quite a lot of fabric bought. This was the haul!


The rippled one really did remind me of the Old Shale stitch pattern (what most people erroneously call Feather and Fan). Though Mr says it makes his eyes funny, so it won't be used for cushion as I'd intended.

These two were from Andover Fabrics' Downton Abbey range.


And the charm pack is one I've been on the look out for - Road 15 by Moda.


My patchwork cushions in the lounge have been very well loved and could do with replacing so hopefully these fabrics will step up and take their place.

I learnt a new crochet stitch that same weekend. Its modern name seems to be Diagonal Box Stitch - a rather uninspiring name. It was fun to do. Michele from Yarn Aloud taught us how to do it. There were a few examples about and I liked the look of it in a finer yarn. 



So after some stash rummaging later, I came up with a ball of zauberball and whizzed through to make a scarf. I used a 4.00mm hook, so it had plenty of drape when worn.  I worked it on the bias to make a rectangle shape instead of a square. I used the entire ball but it wasn't long enough to make a decent sized scarf; so I put a row of buttons on one end, so it could be worn as a cowl.



The spaces between the trebles make good buttonholes, so it can be buttoned up in any way you like.


The pattern has brought out the stripes in the yarn; or is it vice versa, the stripes have brought out the pattern well? Either way I think it's fab.



Comments

Post a Comment

Popular posts from this blog

Substituting Yarn in a Project

By -
Image
So you’ve chosen your pattern, but either you don’t want to use the recommended yarn or you can’t find it to buy. This does not mean you are stuck. Many knitters, especially when they are just learning to knit, get stuck on the idea that you can only use the yarn that the pattern is written with. There are, occasionally, a few projects where it can be quite hard to find an alternative but that is very rare. There are a few factors that you want to think about when changing yarn.  Yarn Thickness The main one is the thickness of the yarn. This is the one factor that you absolutely have to consider. Everything else that I discuss below helps to hone your decision down but yarn thickness is at the core of a project. If you use a thicker yarn, it could make the fabric too dense and often make it impossible to match the gauge of the pattern. If you use a thinner yarn, then it will be more open and airy than intended; there’s more scope with this but some projects such as toys an...
Read more

Photo Tutorial: How to Back a Knitted Blanket

By -
Image
Recently, I was asked to help out with a project. This wonderful blanket (designed by Debbie Abrahams from her book, Blanket and Throws to Knit ) was knitted by Ann. I was asked to piece it together and back it. The finished blanket is being used to raise money for When you Wish Upon a Star. The yarn was donated by A Good Yarn and the fabric and cotton by L & C Fabrics . I thought I’d show you how I went about backing the blanket, I went about it as I would a quilt. Though, I decided tying would be the best way of layering it together, as traditional quilting would be difficult on a knitted fabric. 1. Block the blanket. I pinned it out and spritzed it. Normally, I would wet block, but I was concerned that the red may bleed and it would take some time to dry too. 2. My blanket was too large for a standard width so I pieced the backing. The backing should be a few inches larger than the knitted blanket. Place it right side down on the floor. I then tape it down o...
Read more

Photo Tutorial: Estonian Cast On

By -
Image
I've recently been looking into different cast on methods. I've tried quite a few and they've all got their purpose but I have taken quite a fancy to the Estonian Cast On (a.k.a. Double Start, Latvian). It's quite simple to execute, it's stretchy and can be quite decorative too. It works well with 1 x 1 and 2 x 2 ribbing because it wraps around the base of the column of ribbing. It's a super cast on for socks. The tutorial is for the single strand method. 1. Measure out a long tail. I tend to use 1 inch per stitch for thicker yarn and 1/2 inch per stitch for DK weight and thinner; plus another 6 inches for luck! Make a slip knot and place on your needle. 2. Place your fingers between the strands and tilt your hand back into a catapult position. This creates a cross on the thumb strand. 3. Insert your needle into the loop around your thumb from below. 4. Reach across over the top of the strand on your forefinger. 5. ...
Read more