Mittens just in time for Spring!

By -
My Narwhal mittens are finished. The pattern is Narwhal Mittens by Ysolda.

The yarn for the outer mitten is my own handspun. Briefly, blogged here


The inner yarn is some leftover Easyknits that seem to match well with the teal colour.


I made some plastic templates to block the mitten around because I didn't want to block the inner and the outer separately. I wanted them to fit snuggly inside on another.


Though the template was a bit slapdash, it did seem to work surprisingly well.



I especially like the little finishing touches on the design. The little fish on the ends of the thumbs is lovely.




I love the mittens. The yarn has worked nicely in colourwork and they are very warm. Just perfect for this lovely spring weather we're having!! Would have been a lot better if I'd finished them a few months ago.

The cherry blossom is out....


and the bees have been getting busy!



Comments

Post a Comment

Popular posts from this blog

Substituting Yarn in a Project

By -
Image
So you’ve chosen your pattern, but either you don’t want to use the recommended yarn or you can’t find it to buy. This does not mean you are stuck. Many knitters, especially when they are just learning to knit, get stuck on the idea that you can only use the yarn that the pattern is written with. There are, occasionally, a few projects where it can be quite hard to find an alternative but that is very rare. There are a few factors that you want to think about when changing yarn.  Yarn Thickness The main one is the thickness of the yarn. This is the one factor that you absolutely have to consider. Everything else that I discuss below helps to hone your decision down but yarn thickness is at the core of a project. If you use a thicker yarn, it could make the fabric too dense and often make it impossible to match the gauge of the pattern. If you use a thinner yarn, then it will be more open and airy than intended; there’s more scope with this but some projects such as toys an...
Read more

Photo Tutorial: How to Back a Knitted Blanket

By -
Image
Recently, I was asked to help out with a project. This wonderful blanket (designed by Debbie Abrahams from her book, Blanket and Throws to Knit ) was knitted by Ann. I was asked to piece it together and back it. The finished blanket is being used to raise money for When you Wish Upon a Star. The yarn was donated by A Good Yarn and the fabric and cotton by L & C Fabrics . I thought I’d show you how I went about backing the blanket, I went about it as I would a quilt. Though, I decided tying would be the best way of layering it together, as traditional quilting would be difficult on a knitted fabric. 1. Block the blanket. I pinned it out and spritzed it. Normally, I would wet block, but I was concerned that the red may bleed and it would take some time to dry too. 2. My blanket was too large for a standard width so I pieced the backing. The backing should be a few inches larger than the knitted blanket. Place it right side down on the floor. I then tape it down o...
Read more

Photo Tutorial: Estonian Cast On

By -
Image
I've recently been looking into different cast on methods. I've tried quite a few and they've all got their purpose but I have taken quite a fancy to the Estonian Cast On (a.k.a. Double Start, Latvian). It's quite simple to execute, it's stretchy and can be quite decorative too. It works well with 1 x 1 and 2 x 2 ribbing because it wraps around the base of the column of ribbing. It's a super cast on for socks. The tutorial is for the single strand method. 1. Measure out a long tail. I tend to use 1 inch per stitch for thicker yarn and 1/2 inch per stitch for DK weight and thinner; plus another 6 inches for luck! Make a slip knot and place on your needle. 2. Place your fingers between the strands and tilt your hand back into a catapult position. This creates a cross on the thumb strand. 3. Insert your needle into the loop around your thumb from below. 4. Reach across over the top of the strand on your forefinger. 5. ...
Read more