Review: Knit Pro Karbonz knitting needles

By -
I recently purchased some Knit Pro Karbonz DPNs.



For a start off, they are a work of art. I think they look sleek and quite unusual.

My usual DPNs are the Knit Pro Nova metal ones. I prefer the metal ones to wooden because the stitches move quicker, it speeds up my knitting and I enjoy the process more with metal needles.

I've knitted a pair of socks in the Karbonz. The pros are that I can see is they are lightweight, flexible, warm to the touch (a benefit for those with arthritis or other issues with their hands) and the stitches are less likely to drop off the needles (they have a similar surface to wood, which is a bit more clingy than metal). In general, I prefer them to wooden needles. Though lightweight, they have a better balance to them than say the Symfonie wooden range. They have the benefits of wooden needles but with the extra pointyness of metal needles. If you are a knitter that prefers wooden needles then it is seems to be a good middle ground between the metal and wooden ones.
Top needle: Karbonz
Bottom needle: Nova
Shows same size needle.

The only downside is the join between the metal tips and the carbon. Don't get me wrong the yarn doesn't catch at the join, it's a smooth join but I'm aware of the difference with how the stitches move from one to the other. I'm perhaps being a little too picky with this and it doesn't put me off them. Though, (especially with the higher purchase price), I won't be changing all my current Nova needles to the Karbonz.

I'll be quite happy to use the current set I have. I've compared them to other Knit Pro needles, as I thought this was fairest since it focused more on material than make. I have other makes of needles too such as HiyaHiya and Addi, which I've always been happy with too. Knit Pro seem to strike a good balance between quality and value for money.

 A little photo of my current WIP, made using my Karbonz.


Comments

Post a Comment

Popular posts from this blog

Substituting Yarn in a Project

By -
Image
So you’ve chosen your pattern, but either you don’t want to use the recommended yarn or you can’t find it to buy. This does not mean you are stuck. Many knitters, especially when they are just learning to knit, get stuck on the idea that you can only use the yarn that the pattern is written with. There are, occasionally, a few projects where it can be quite hard to find an alternative but that is very rare. There are a few factors that you want to think about when changing yarn.  Yarn Thickness The main one is the thickness of the yarn. This is the one factor that you absolutely have to consider. Everything else that I discuss below helps to hone your decision down but yarn thickness is at the core of a project. If you use a thicker yarn, it could make the fabric too dense and often make it impossible to match the gauge of the pattern. If you use a thinner yarn, then it will be more open and airy than intended; there’s more scope with this but some projects such as toys an...
Read more

Photo Tutorial: How to Back a Knitted Blanket

By -
Image
Recently, I was asked to help out with a project. This wonderful blanket (designed by Debbie Abrahams from her book, Blanket and Throws to Knit ) was knitted by Ann. I was asked to piece it together and back it. The finished blanket is being used to raise money for When you Wish Upon a Star. The yarn was donated by A Good Yarn and the fabric and cotton by L & C Fabrics . I thought I’d show you how I went about backing the blanket, I went about it as I would a quilt. Though, I decided tying would be the best way of layering it together, as traditional quilting would be difficult on a knitted fabric. 1. Block the blanket. I pinned it out and spritzed it. Normally, I would wet block, but I was concerned that the red may bleed and it would take some time to dry too. 2. My blanket was too large for a standard width so I pieced the backing. The backing should be a few inches larger than the knitted blanket. Place it right side down on the floor. I then tape it down o...
Read more

Photo Tutorial: Estonian Cast On

By -
Image
I've recently been looking into different cast on methods. I've tried quite a few and they've all got their purpose but I have taken quite a fancy to the Estonian Cast On (a.k.a. Double Start, Latvian). It's quite simple to execute, it's stretchy and can be quite decorative too. It works well with 1 x 1 and 2 x 2 ribbing because it wraps around the base of the column of ribbing. It's a super cast on for socks. The tutorial is for the single strand method. 1. Measure out a long tail. I tend to use 1 inch per stitch for thicker yarn and 1/2 inch per stitch for DK weight and thinner; plus another 6 inches for luck! Make a slip knot and place on your needle. 2. Place your fingers between the strands and tilt your hand back into a catapult position. This creates a cross on the thumb strand. 3. Insert your needle into the loop around your thumb from below. 4. Reach across over the top of the strand on your forefinger. 5. ...
Read more